Time limit: 0
Quiz Summary
0 of 13 Questions completed
Questions:
Information
You have already completed the quiz before. Hence you can not start it again.
Quiz is loading…
You must sign in or sign up to start the quiz.
You must first complete the following:
Results
Quiz complete. Results are being recorded.
Results
0 of 13 Questions answered correctly
Your time:
Time has elapsed
You have reached 0 of 0 point(s), (0)
Earned Point(s): 0 of 0, (0)
0 Essay(s) Pending (Possible Point(s): 0)
Categories
- Not categorized 0%
-
Unfortunately, you didn’t pass the quiz, but hey, you have unlimited access.😎
Practice makes you perfect! 👊 -
Congratulations! 🥳
You have passed the quiz successfully! You are one step closer to pass the real exam!
We hope to see you again on another certification path.✌️
Good luck with the exam! Stay strong.👊
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- Current
- Review
- Answered
- Correct
- Incorrect
-
Question 1 of 13
1. Question
The senior network engineer of your company, tells you to configure the interfaces of the R1 based on the diagram below.
The subnet mask is
255.255.255.0
.
Start the configuration with theG0/0
, thenG0/1
and lastS0/0
-
R1#
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#
R1(config-if)#
R1(config-if)#
R1(config-if)#
R1(config-if)#
R1(config-if)#
R1(config-if)#
R1(config-if)#
R1(config-if)#
R1(config-if)# ^Z
R1#
CorrectIncorrect -
-
Question 2 of 13
2. Question
Type the command that produces the following output.
-
ExamsDigestR1#
Global values:
Internet Protocol routing is enabled
Embedded-Service-Engine0/0 is administratively down, line protocol is down
GigabitEthernet0/0 is up, line protocol is up
Internet address is 158.16.1.1/24
GigabitEthernet0/1 is administratively down, line protocol is down
Serial0/0/0 is up, line protocol is up
Internet address is 158.16.4.1/24
Serial0/0/1 is administratively down, line protocol is down
GigabitEthernet0/1/0 is up, line protocol is up
Internet address is 158.16.1.1/24
CorrectIncorrect -
-
Question 3 of 13
3. Question
Match the commands with the respective purpose.
Sort elements
- show interfaces [type number]
- ip address [address mask]
- interface [type number]
- show ip interface brief
-
Lists a large set of informational messages about each interface, or about the one specifically listed interface.
-
Interface subcommand that sets the router’s IPv4 address and mask.
-
Global command that moves the user into configuration mode of the named interface.
-
Lists a single line of information about each interface, including the IP address, line and protocol status, and the method with which the address was configured.
CorrectIncorrect -
Question 4 of 13
4. Question
After configuring a working router interface with IP address/mask 10.1.1.100/26, which of the following routes would you expect to see in the output of the
show ip route
command? (Choose two answers.)CorrectIncorrect -
Question 5 of 13
5. Question
You are responsible to configure a static route for the network 156.187.45.0/24 using the IP address 156.187.80.45 as the next-hop IP. Type the command to configure the static route.
CorrectIncorrect -
-
Question 6 of 13
6. Question
A router lists the following partial output from the
show ip route
command. Out which interface will the router route packets destined to IP address 180.5.38.122?
10.0.0.0/8 is variably subnetted, 8 subnets, 5 masks
O 180.5.38.100/32 [110/50] via 172.16.25.2, 00:00:04, GigabitEthernet0/0/0
O 180.5.38.64/26 [110/100] via 172.16.25.129, 00:00:09, GigabitEthernet0/1/0
O 180.5.37.0/23 [110/65] via 172.16.24.2, 00:00:04, GigabitEthernet0/2/0
O 180.5.38.96/27 [110/65] via 172.16.24.129, 00:00:09, GigabitEthernet0/3/0
O 0.0.0.0/0 [110/129] via 172.16.25.129, 00:00:09, GigabitEthernet0/0/0CorrectIncorrect -
Question 7 of 13
7. Question
Type the commands that produce the following outputs.
-
List the router’s entire routing table:
List the details of static routes only:
List detailed information about the route 156.10.2.0:
CorrectIncorrect -
-
Question 8 of 13
8. Question
A network engineer has configured a Layer 3 switch with SVIs for VLANs 4 and 5. Hosts in the subnets using VLANs 4 and 5 can ping each other with the Layer 3 switch routing the packets. The next week, the network engineer receives a call that those same users can no longer ping each other. If the problem is with the Layer 3 switching function, which of the following could have caused the problem? (Choose two answers.)
CorrectIncorrect -
Question 9 of 13
9. Question
A LAN design uses a Layer 3 EtherChannel between two switches SW1 and SW2, with port-channel interface 1 used on both switches. SW1 uses ports G0/1 and G0/2 in the channel. However, only interface G0/1 is bundled into the channel and working. Think about the configuration settings on port G0/2 that could have existed before adding G0/2 to the EtherChannel. Which answers identify a setting that could prevent IOS from adding G0/2 to the Layer 3 EtherChannel? (Choose two answers.)
CorrectIncorrect -
Question 10 of 13
10. Question
Type the command that enables a switch interface to be a routed interface instead of a switched interface
CorrectIncorrect -
-
Question 11 of 13
11. Question
You have noticed that a server with IP 145.45.3.2 doesn’t respond to requests. What command will you type first in order to test the connectivity between your device and the server?
CorrectIncorrect -
-
Question 12 of 13
12. Question
The commands
ping
andtraceroute
send messages in the network to test connectivity and rely on other devices to send back a replyCorrectIncorrect -
Question 13 of 13
13. Question
You are connected on a router R1, type the command to connect to R2 using SSH.
Use the following login credentials in order to get access to R2.
R2’s IP address: 145.167.2.1
username: userexamsdigest
password: passexamsdigest
-
R1#
R2>
CorrectIncorrect -